Home

Printing setup
Nozzle temp. – 190° C – 210° C
Bed temp. – 40° C – 60° C
Fan – 50% – 100 %
Printing speed – 100 mm/s or more
Enclosure – No need

The ESP32-ESP-WROOM-32 development kit is an ideal kit for learning how to program the ESP-WROOM-32 module and testing its capabilities. One board contains the above-mentioned communication module / micro-controller, a USB -> UART interface based on the CP2102 chip, buttons that facilitate switching the device to programming mode and a voltage converter thanks to which the whole thing is powered directly from the micro USB connector. In addition, all pins of the ESP-WROOM module are provided as goldpin connectors, so the module can be used with any breadboard without the need for soldering. The device allows you to use Wi-Fi (802.1 b/g/n), Bluetooth / Bluetooth LE protocols and, if necessary, your own protocols written by the user.

Amplifier InternalImpedance 4 OhmPower RMS (W) 2 x 3Product type SpeakerSystem type 2.0Τροφοδοσία USBColor White

Printing setup
Nozzle temp. – 240° C – 260° C
Bed temp. – 75° C – 90° C
Fan – 0% – 50%
Printing speed – 50 mm/s -100 mm/s
Enclosure – No need

Printing setup
Nozzle temp. – 240° C – 260° C
Bed temp. – 75° C – 90° C
Fan – 0% – 50%
Printing speed – 50 mm/s -100 mm/s
Enclosure – No need

Printing setup
Nozzle temp. – 240° C – 260° C
Bed temp. – 75° C – 90° C
Fan – 0% – 50%
Printing speed – 50 mm/s -100 mm/s
Enclosure – No need

Printing setup
Nozzle temp. – 190° C – 210° C
Bed temp. – 40° C – 60° C
Fan – 50% – 100 %
Printing speed – 100 mm/s or more
Enclosure – No need

Printing setup
Nozzle temp. – 240° C – 260° C
Bed temp. – 75° C – 90° C
Fan – 0% – 50%
Printing speed – 50 mm/s -100 mm/s
Enclosure – No need

Printing setup
Nozzle temp. – 240° C – 260° C
Bed temp. – 75° C – 90° C
Fan – 0% – 50%
Printing speed – 50 mm/s -100 mm/s
Enclosure – No need

Printing setup
Nozzle temp. – 240° C – 260° C
Bed temp. – 75° C – 90° C
Fan – 0% – 50%
Printing speed – 50 mm/s -100 mm/s
Enclosure – No need

Printing setup
Nozzle temp. – 240° C – 260° C
Bed temp. – 75° C – 90° C
Fan – 0% – 50%
Printing speed – 50 mm/s -100 mm/s
Enclosure – No need

Printing setup
Nozzle temp. – 190° C – 210° C
Bed temp. – 40° C – 60° C
Fan – 50% – 100 %
Printing speed – 100 mm/s or more
Enclosure – No need

Printing setup
Nozzle temp. – 190° C – 210° C
Bed temp. – 40° C – 60° C
Fan – 50% – 100 %
Printing speed – 100 mm/s or more
Enclosure – No need

Printing setup
Nozzle temp. – 190° C – 210° C
Bed temp. – 40° C – 60° C
Fan – 50% – 100 %
Printing speed – 100 mm/s or more
Enclosure – No need

Printing setup
Nozzle temp. – 190° C – 210° C
Bed temp. – 40° C – 60° C
Fan – 50% – 100 %
Printing speed – 100 mm/s or more
Enclosure – No need

Printing setup
Nozzle temp. – 190° C – 210° C
Bed temp. – 40° C – 60° C
Fan – 50% – 100 %
Printing speed – 100 mm/s or more
Enclosure – No need

The ESP32-ESP-WROOM-32 development kit is an ideal kit for learning how to program the ESP-WROOM-32 module and testing its capabilities. One board contains the above-mentioned communication module / micro-controller, a USB -> UART interface based on the CP2102 chip, buttons that facilitate switching the device to programming mode and a voltage converter thanks to which the whole thing is powered directly from the micro USB connector. In addition, all pins of the ESP-WROOM module are provided as goldpin connectors, so the module can be used with any breadboard without the need for soldering. The device allows you to use Wi-Fi (802.1 b/g/n), Bluetooth / Bluetooth LE protocols and, if necessary, your own protocols written by the user.

Printing setup
Nozzle temp. – 240° C – 260° C
Bed temp. – 75° C – 90° C
Fan – 0% – 50%
Printing speed – 50 mm/s -100 mm/s
Enclosure – No need

Printing setup
Nozzle temp. – 190° C – 210° C
Bed temp. – 40° C – 60° C
Fan – 50% – 100 %
Printing speed – 100 mm/s or more
Enclosure – No need

Printing setup
Nozzle temp. – 190° C – 210° C
Bed temp. – 40° C – 60° C
Fan – 50% – 100 %
Printing speed – 100 mm/s or more
Enclosure – No need

Printing setup
Nozzle temp. – 240° C – 260° C
Bed temp. – 75° C – 90° C
Fan – 0% – 50%
Printing speed – 50 mm/s -100 mm/s
Enclosure – No need